Preparation of molecularly imprinted fluorescence sensor based on carbon quantum dots via precipitation polymerization for fluorescence detection of tetracycline

A facile and effective method was proposed to prepare the molecularly imprinted fluorescence sensor with carbon quantum dots, which were modified vinyl groups by acrylic acid on the surface. The obtained fluorescence composite material was investigated by transmission electron microscope and Fourier transform infrared spectra. After the experimental conditions were optimized, a linear range of 1.0–60 μmol L⁻¹ was obtained and the detection limit was 0.17 μmol L⁻¹. The novel fluorescence sensor can be successfully used to detect tetracycline in real samples. This study provides a convenient strategy for selective recognition and rapid detection of tetracycline in the complex environment.     

Cobalt doping of α-Fe/Al2O3 catalysts for the production of hydrogen and high-quality carbon nanotubes by thermal decomposition of methane

Fe–Co/Al₂O₃ catalysts were developed and tested in the catalytic decomposition of methane (CDM) for the synthesis of multi-wall carbon nanotubes (MWCNT) and the CO₂-free hydrogen production. While Fe (54.5–66.7 mol.%) is the main active phase for the carbon formation on the catalyst, Co acts as dopant aiming to improve its overall catalytic behaviour. Catalysts with Co contents of up to 18.2 M% showed the presence of α-Fe and Fe–Co crystallites with different size and lattice parameter. Fe_1-xCo_x alloy with bcc crystal system was identified only for Co contents of 14.0% and above, and presented a lattice constant lower than α-Fe, which would modify the carbon diffusion of the metal particle during the MWCNT growth. Co inhibited the Fe₃C formation during CDM resulting in higher carbon formations and longer activity times. This phase, shown in undoped catalysts, favored the presence of bamboo-type carbon nanotubes.     

基于CFD-DEM方法的净化器流场模拟与结构优化

针对空气净化器能耗高的问题，使用离散元方法(DEM)在吸附滤网中建立随机堆积柱形活性炭模型，采用计算流体力学(CFD)方法对空气净化器内部流场进行数值模拟，在模拟与实验验证的基础上，考察了压降最小、流场最均匀的吸附滤网结构。结果表明，空气净化器压降主要发生在轴向，活性炭吸附滤网中回流、沟流现象严重，流体阻力是其他两种滤网的3倍。边数对多边形填充孔结构吸附滤网内压降与流场均匀性无影响，当孔结构改为圆形时，压降减小约52 Pa，节能18.4%(49 W)；当孔直径由8 mm增至12 mm，压降减小约48 Pa，节能19.4%(45 W)；滤网间距对空气净化器压降无影响，圆形、小孔径的吸附滤网内流场最均匀。     

改性氧化钛对羟乙基乙二胺水溶液解吸CO2的强化

羟乙基乙二胺（AEE）水溶液的CO₂循环吸收量高（1.2molCO₂/molAEE），吸收速度快，稳定性好，但解吸速度慢、解吸量少（0.8mol CO₂/mol AEE）是限制该技术广泛应用的主要原因。本文通过向AEE水溶液中添加质量分数为0.05%～0.20%的改性氧化钛（TiO₂-MWCNT和TiO₂-OH）强化AEE的解吸能力。CO₂循环吸收（40℃）-解吸（120℃）实验结果表明改性氧化钛的添加比氧化钛强化CO₂解吸效果更好，强化顺序为TiO₂-MWCNT＞TiO₂-OH；其对应的最大解吸速率分别为0.093L/min（质量分数0.15%）和0.083L/min（质量分数0.20%），相对于AEE水溶液，分别提高了32.9%和18.6%；其对应的最大解吸量分别为0.92molCO₂/molAEE（质量分数0.15%）和0.88molCO₂/molAEE（质量分数0.20%），分别提高了12.2%和9.7%；其对应的CO₂循环吸收量分别是0.95molCO₂/molAEE（质量分数0.15%）和0.89molCO₂/molAEE（质量分数0.15%），分别提高了18.75%和11.25%；5次循环吸收解吸实验结果表明改性氧化钛强化CO₂解吸效果稳定，具有较强的化学稳定性。对反应后的改性氧化钛进行XRD、BET、FTIR和SEM表征，结果表明改性氧化钛具有较强的结构稳定性。TiO₂-MWCNT和TiO₂-OH在促进有机胺溶液解吸CO₂方面具有一定的工业应用潜力。     

氧化石墨烯改性碳纤维复合材料抗冲击行为研究

使用单层纳米氧化石墨烯（NGO）粒子对环氧树脂进行改性处理，采用真空辅助树脂传递模塑成型工艺制备了[±45/0/90]_2S铺层角度下的纯树脂及单层NGO改性碳纤维复合材料（CFRP）层合板。通过落锤冲击试验、超声C扫描检测、冲击后压缩试验等对纯树脂及单层NGO改性CFRP进行实验研究。结果表明，纯树脂及单层NGO改性CFRP在损伤阻抗及损伤容限实验中均存在拐点现象，且拐点出现在相同深度位置，其中纯树脂CFRP拐点位置为0.51 mm，单层NGO改性CFRP拐点位置为0.43 mm；相对于纯树脂CFRP，单层NGO改性CFRP可以显著提高复合材料的抗冲击性能及冲击后的压缩性能；通过对冲击后凹坑深度及凹坑面积进行数据模拟，可以用拟合公式实现对复合材料的损伤预测。     

二硫化钼纳米片用于修饰微生物燃料电池阳极的研究

利用简单的一步水热法制备了MoS2纳米片并用于修饰不锈钢纤维毡阳极(MoS2-SSFF),与未修饰不锈钢纤维毡阳极(SSFF)和多壁碳纳米管修饰阳极(CNT-SSFF)进行了对比研究。装配MFC运行的测试结果表明,MoS2-SSFF/MFC的功率密度为714 m W/m2,略高于CNT-SSFF/MFC的功率密度693 m W/m2,远高于未修饰SSFF/MFC的功率密度197 m W/m2。利用扫描电子显微镜(SEM)观察到MoS2纳米片呈簇状附着于MoS2-SSFF电极表面,显著增加了电极的比表面积。MoS2纳米片修饰改善了SSFF阳极的生物相容性,修饰电极在循环伏安测试(CV)中表现出良好的氧化还原性能。水热法制备的MoS2纳米片用于修饰阳极是一种高效、经济、简单的阳极修饰方法。     

Microwave pyrolysis of polystyrene and polypropylene mixtures using different activated carbon from biomass

In this study, microwave pyrolysis was experimented with mixed types of plastic waste. Two different plastic wastes polystyrene waste (PSW) and polypropylene waste (PPW) were used as feedstock. Carbon and activated carbon were synthesized from different biomass; rice husk (RH), corn husk (CH) and coconut sheath (CS) respectively which are used as microwave susceptors. The effect of impregnation on product yields was studied. Microwave pyrolysis at 900 W and with a polymer to an absorbent ratio of 10:1, produced the highest oil yield of 84.30 wt% when coconut sheath activated carbon (CSAC) was used as an absorbent. The reaction time was 10 min for the complete decomposition of polymer mixtures. Oil properties were determined and a high calorific value of 46.87 MJ kg⁻¹ was obtained. These properties were compared to conventional fuel properties and the product oil has a density of 0.76 g ml⁻¹ and viscosity of 2.4 cSt which is an equivalent fraction obtained to that of gasoline. Product oil has a styrene recovery of 67.58% from microwave pyrolysis. The results demonstrate that, microwave pyrolysis has a great potential for energy recovery from mixed plastic waste and the use of agricultural residues as absorbents enhanced the production efficiency of the process.     

Structure,properties, and applications of polyacrylonitrile/carbon nanotube (CNT) fibers at low CNT loading

Bi-component, polyacrylonitrile (PAN)/carbon nanotube (CNT) fibers were processed, at different core-sheath area ratios, by gel spinning. A percolated CNT network at 10 wt% CNT in the sheath enhanced electrical conductivity as compared to the neat PAN fiber, while PAN polymer in the core contributed to the good mechanical properties. Fibers with relatively thin sheath allowed overall CNT loading as low as 3.7 wt% to be made with good electrical conductivity, and PAN stabilization by Joule heating was demonstrated. Such fibers with combined good mechanical properties and electrical conductivity can also potentially be used for electrical heating of fabrics, for making smart textiles, and for electromagnetic interference shielding.     

Composite mixed matrix membranes incorporating microporous carbon molecular sieve as filler in polyethersulfone for CO2/CH4 separation

Membrane technology has been considered a key factor for sustainable growth in high-efficiency gas separation. Current mixed matrix membranes (MMMs) technology is rising, but these membranes in the dense structure are having difficulties in operating at high pressures and scale up for commercialization. The purpose of this research is to synthesize composite MMMs (CMMMs) consisting of polyethersulfone (PES), carbon molecular sieve (CMS 1–5 wt %), and Novatex 2471 nonwoven fabric (support layer). The membranes' physical, chemical, and thermal properties were evaluated by different analytical equipment. The morphology of both PES and PES-CMS composite membranes had a porous and asymmetric structure, in which CMS was uniformly distributed in the polymer matrix. The thermal properties showed that the membranes were stable up to 350 °C with a single glass transition temperature. The functional groups in the membrane were confirmed by spectral analysis. The gas performance results showed that carbon dioxide permeance increased with increased CMS concentration and methane permeance decreased due to the hindering effect of CMS under similar operating conditions. The highest selectivity achieved was 12.774 using CMMM of 5 wt % of CMS at 10 bar, which on average was 137.80%, improved selectivity compared to pure PES membrane. The support layer was able to withstand high operating pressures and showed the ability to scale up. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48476.